EP brand replacement gearbox for woods rotary gearbox

EP manufacturer substitute gearbox for woods rotary gearbox

NEW forty HP GEARBOX Sleek Input one 3/8 12 spline output Interchangable with marketplace well-liked size i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Numerous Much more

Functions
(1) brand new forty five horse energy shearpin gearbox. This gearbox matches several distinct tends to make of 4′,5′ and some 6′ rotary cutters. I offer a whole lot of these containers each 12 months for a number of various apps and have ALL Substitute Components for this box, but hopefully you won’t have to fret about that.
Below are the specs on the box:
*45 horse electrical power gearbox
*Standard one-3/8″ clean input shaft(exactly where the pto shaft hooks on). The pto shaft is held on by a 1/two shearbolt.
*size of the input shaft out of the gearbox is three” prolonged
*bolt hole sample for mounting is on the corners, 4-3/four centre of gap to center of gap. It takes a five/8″ bolt.
*twelve splined output shaft(the place the blade carrier hooks up on the bottom)
*1-nine/sixteen exterior measurement above the output shaft splines- from the foundation of the output cap to the finish of the splines is 2-3/4″ extended- general size of the output shaft is four-one/two” long.
*will take a 1″ threaded castle nut and a carter essential on the base of the output shaft to safe blade pan(NUT is provided – – BLADE PAN IS NOT!!)
*total peak of the box from the prime of the mower deck to the top of the box is nine-one/two”
This is a fairly weighty item (47 lbs.) so freight is not low-cost, but we do not make something off of freight, no matter what ups costs us we cost you.
forty HP
one:one:forty seven Ratio
one-three/8″ Sleek Input Shaft with Shear Pin Hole
1-1/two” twelve-Spline Ouput Shaft
Bolt Pattern: 6-1/two” (four) 5/8″ Holes, five” Center Gap Required for Shaft Assembly
The Input and Output Shafts Are not able to be Purchased Serparately.
They are Sold as a package.
The kit involves the adhering to areas: input shaft, enter equipment, output shaft, output equipment.
The Shaft Package Cannot Be Divided.

EP brand name alternative gearbox for woods rotary gearbox

Rotary Cutter Gearbox Troubleshooting Guidebook
Is your mower leaking, creaking or otherwise doing improperly? You’ve occur to the appropriate place.

Study underneath for the most common troubles with rotary cutter gearboxes and their answers (from quick and soiled, to expert).

Leaking Bottom Seal:
If you’ve got wrapped some baling or fencing wire around your output shaft and blown the seal, the skilled issue to do is to change the seal.
If your output seal is intact, and you are ready to get ID, OD and thickness measurements (in millimeters), most bearing houses can get you up a generic double-lip seal that will get you back up-and-running. If not, give us a get in touch with and we can help you type out what you require.
A dental choose is the best way to take away the old seal just before pressing in the new a single.
If you might be blessed sufficient to have a sluggish-leak, the quick and soiled approach is to operate automotive-sort grease in the gearbox until the new seal comes in. Be certain to verify and include grease far more usually than you would with oil, as this is NOT a professional fix.

Damaged Output Shaft:
Uh oh. You strike something that didn’t transfer. The good information is that the output shaft on most gearboxes is reasonably effortless to substitute. The bad news is… it really is rarely an isolated failure.
The initial point to do is to consider apart your gearbox and assess the entire extent of the hurt. If it is really just the output shaft, you must be ready to alter it out, no difficulty. The output shafts begin at about $70 and go up in price tag depending on the measurement of the gearbox.
However, in most instances, the bearings ($20/ea), seals ($ten/ea) and gear-established ($70) will also generally get a beating. If you happen to be unfortunate, the output cap ($eighty) will also suffer some harm.
In this scenario, it is typically less costly to change the gearbox. Compare the value of areas to the price of an complete, new, warrantied gearbox. Often, even professionals have to know when to phone it a day.

I Want to Alter my Input Shaft:
If you are exhausted of altering shear pins or looking back and viewing that your mower has not been reducing, you may want to set up a slip-clutch pto shaft (Sure, we promote those also).
This generally calls for setting up a 540-fashion, 6-spline enter shaft ($85) on your mower’s gearbox.
Lucky for you, we did a compose-up on our site. It is known as “How to change the input shaft on your rotary cutter gearbox”.

My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all seem variety-of similar above-the-phone. The greatest thing to do is to disassemble your gearbox and consider a search at the gears and bearings. The problem will generally present by itself in the way of damaged/missing equipment enamel, toasted gears (like that photo on our property page), or blown bearings.
If every thing seems standard, consider adjusting the equipment-mesh. This is done with the mylar “gaskets” that sit amongst the main gearbox scenario and the enter/output caps. Try including or removing some of these spacers right up until your gears have around one/eight”-one/4″ of totally free perform. Professionals can buy replacements ($1-two) in different thicknesses, but we advise the rapid and dirty approach of cutting your possess out of a sheet of mylar.
Will not overlook to re-seal the gearbox with RTV soon after you’ve got identified the proper combination. Even however they are referred to as “gaskets”, they won’t seal your gearbox on their possess.

If this article really did not fulfill your interest worrying Gearbox For Trenchers – Soil Tillage, inspect these extra ones out.